SWORKz S35-GT3.0 FTE Factory Team Edition 1/8 Nitro GT Pro Kit
Product information "SWORKz S35-GT3.0 FTE Factory Team Edition 1/8 Nitro GT Pro Kit"
| Brand: | SWORKz |
|---|---|
| Size: | 1/8 |
| Type: | Nitro |
| Version: | 4WD, GT, Kit, Nitro |
| Application: | Nitro |
The project of GT3.0 Factory Team Edition(FTE) is a special product for SWORKz GT worlds drivers to compete in the 2025 IFMAR GT World Championships. The target is to be faster, lighter and easier driving performance.
The Car is designed with high quality aluminum bulk heads that can change diff positions. A Direct response steering servo savor with a new Ackerman system.
The latest S35-GT3.0 FTE series has a latest designed from the front flat bumper design. It’s an on road concept on GT, to make the new GT car even more faster.
Lay Down Shock Tower System has a new suspension geometry to lay-down the shock positions. This is especially designed for high speed on road racing. Specially included options are the S35-GT2.2 front upper and lower ultra hard material arms. Also included are the latest S35-4 EVO rear lower ABS arms (ultra hard material) that improves the S35-GT3.0 FTE's cornering speeds. A new pipe extension holder spring plate that allows the pipe to sit closer to the body shell.
The 2-speed transmission has also been completely revised on the S35-GT2.2 platform that significantly improved compared to its predecessor.
The S35-GT3.0 FTE comes standard with a new SWORKz Tornado GT 4-Shoes Clutch and Tornado GT 4-Shoes Aluminum Clutch Bell to get the maximum power from the engine to the transmission.
The S35-GT3.0 has a weight-optimized, silver anodized base chassis plate made of high-strength T7075 aluminum.
The HET differentials developed by SWORKz are also included with 13T pinion and 45T crowns in the kit.
The wishbone brackets, included with duranbl square inserts, allow the axle geometry of your SWORKz S35-GT3.0 FTE to be adapted to any track layout. The front and rear CVD wishbones are made of a newly developed composite material. The side pans have also been redesigned.
The SWORKz S35-GT3.0 FTE has a new design rear knuckles plates made from composite materials combined with carbon plates that offers you the possibility for different setups.
There are many other changes and new ideas that were incorporated into the SWORKz S35-GT3.0 FTE that makes this car a real winner.
S35-GT3.0 FTE FEATURES
- New Weight-optimized, Silver Anodized T7075 base chassis plate
- New Front & Rear Shock Pro-composite Carbon Shock Towers
- New Composite Carbon Extension Pipe Holders
- Shock End Extension Holders with Pin-Screws
- New Front and Rear Adjustable Diff Position Design
- New Lightened Aluminum Front & Rear Diff Case Design
- New Aluminum Diff. Case Inserts
- New Aluminum Lower Arm Plates
- Aluminum Front Upper Arm Holder
- New Front & Rear Aluminum Chassis Brace
- New Center One-Unit Brace Holder
- New Pro Aluminum Ackerman Steering Plate
- Aluminum Servo Savor Steering System
- Comes standard with Ultra Hard Arms Front & Rear
- Comes standard with Ultra Hard Upper Arms Front
- Multi-adjustable Sway Bar Linkage System for Front & Rear
- Comes standard with HET Over Drive Gears (45T/13T)
- 2 Front Chassis Struts
- More balance weight positions
- Optimized composite T7075 aluminum parts
- Comes standard with Hard Material Center Spur Gears (58/62T)(Made in Italy)
- New Tornado GT 4-Shoes Clutch Kit
- New Tornado GT 4-Shoes Aluminum Clutch Bell
- Length: 500mm
- Width: 308mm
- Height: 145mm
- Ground Clearance: 15mm
- Wheelbase: 325-330mm
- Track: F 306mm / R 308mm
- Gear Ratio: C 58/62, 19/24T, F/R 45/13T
- Weight: Kit weight 3070g (Full equipment with fuel, without Tires and Body Shell)